Why Is My Pan Not Heating Evenly on Induction?

Uneven heating on induction is almost always one of three things: a warped or non-flat base, a pan bigger than its heating zone, or a thin base that can’t spread heat fast enough — not a flaw in induction itself. Check the base against a flat surface first, since that single test rules out the most common cause.

Induction heats the metal directly above its coil, so any mismatch between pan and coil geometry shows up as uneven heat more obviously than it would on gas, where the flame spreads out underneath regardless of the pan’s shape.

The short answer

  • Warped base: the single most common cause. Even a slight curve stops the pan sitting flat against the glass.
  • Pan bigger than the zone: the center over the coil gets more heat than the edges hanging outside the zone’s field.
  • Thin or low-quality base: can’t spread heat fast enough, so it concentrates directly over the coil.
  • Ring-pattern coils can leave a cold spot in the exact center of the pan, especially on large pots and Dutch ovens.
  • Burnt residue or oil buildup on the base disrupts even contact and heat transfer.
  • Fix: flat-base test, match pan size to zone, preheat on medium rather than high, and favor pans with a thick multi-layer base.

1. Cause 1: a warped or curved base

Even a slight curve in a pan’s base keeps it from sitting flat against the induction glass, and the gap that creates means some areas of the base lose direct contact with the magnetic field entirely while others stay in full contact. The result is hot and cool patches that don’t correspond to anything you’re doing wrong in the cooking itself.

How to check: set the pan upside down on a flat countertop or run a straightedge across the base. Any visible rocking or light showing under the edge means it’s warped. Thin stainless and some thin carbon steel pans are the most prone to this, especially after being heated empty or heated too fast — see the warping discussion in my frying pan guide for which specific products have reported this issue.

2. Cause 2: pan bigger than the zone

Induction cooktops only generate heat in the metal directly within a zone’s magnetic field. If your pan’s base extends well beyond that field, the center directly over the coil gets consistent heat while the overhanging edges get little to none — this shows up as a hot center and cool rim, most noticeably on wide pans like griddles and paella pans. This isn’t a defect; it’s physics. See my pan size guide for how to match pan diameter to zone size, and check whether your cooktop has a bridge-zone feature that links two burners for oversized cookware.

3. Cause 3: a thin or low-quality base

A thin, single-layer base can’t spread heat sideways fast enough to keep up with how quickly induction delivers it, so heat stays concentrated in a smaller area directly above the coil rather than spreading evenly across the whole base. Multi-layer pans with an aluminum or copper core sandwiched inside stainless steel spread heat far more evenly than a thin single-layer pan of the same size, because that core conducts heat sideways much faster than stainless alone.

4. Why the center sometimes stays cold

Some induction coils are built as a ring rather than a solid disc, which concentrates the magnetic field in a circle rather than across the whole base. On a large pot or Dutch oven, this can leave a cooler spot in the exact center that’s slower to catch up to the surrounding ring of heat, especially at lower power settings. This is more noticeable on bigger cookware and tends to even out somewhat once the pan comes fully up to temperature.

5. How to fix it

  • Run the flat-base test described above before blaming the cooktop.
  • Match your pan’s base diameter to the zone size rather than always reaching for your biggest pan.
  • Preheat gradually on medium rather than starting on the highest setting, which gives heat more time to spread before you start cooking.
  • Clean the base regularly — burnt residue and oil buildup create their own contact gaps.
  • When buying new cookware, favor a multi-layer (clad) construction over a single thin layer of metal.

FAQ

Is uneven heating normal on induction cooktops?

Some unevenness is normal, especially with large pans or ring-style coils, but significant hot and cold spots usually trace back to a warped base, a size mismatch, or a thin pan. It’s rarely a sign the cooktop itself is faulty.

Why does the center of my pot stay cold on induction?

Some induction coils are ring-shaped, concentrating heat in a circle rather than the exact center. This is most noticeable on large pots and Dutch oven’s at lower power settings and tends to even out as the whole pan comes up to temperature.

Can a warped pan be fixed?

Not reliably — a warped base is usually a sign to replace the pan, since reshaping metal at home rarely restores a truly flat surface, and continuing to use a warped pan on induction will keep producing uneven results.

Does preheating slowly actually help with even heating?

Yes — preheating on medium rather than high gives heat more time to spread sideways through the base before you start cooking, which reduces the gap between the hottest and coolest points on the pan.